H beam 360° Overturning Device ,H Beam Rotator With 4x1.5 KW Motors , 5T Capacity I Beam Rotator

H-section steel is a more efficient cross-sectional area distribution, stronger than the more reasonable economic section of high-performance profiles, because of its cross-section and the English letter "H" the same name. Because H-shaped steel parts are arranged at right angles, so H-shaped steel in all directions have a strong bending ability, simple construction, cost savings and light weight structure, etc., has been widely used.
Chain flip machine, which consists of four pillars. The upper part of the column has a transition sprocket, a passive sprocket and a sprocket. There is a swing arm on the column, one end of the swing arm and the upper wheel on the column between the dynamic match, the other end of the bearing sprocket. Each of the two longitudinally symmetrically arranged upper sprockets, the inner driven sprockets, the sprockets, the lower sprockets and the load sprockets on the swing arm are wound around a conveyor belt, one of which There are motors on the column and reducer, the motor and reducer output shaft on the active sprocket. Install the motor on the intermediate shaft of the motor has a passive sprocket, the outer passive sprocket through the drive chain and the active sprocket connected. The column is also provided with a jacking cylinder, the upper and lower ends of the lifting cylinder are respectively hinged in the middle of the corresponding swing arm and the lower part of the column. The utility model has the advantages of simple structure, low production cost and no hidden danger. Applicable to H-beam, box-beam production line to be welded parts to flip.

Equipment usage

1. This machine is designed to change position of heavy products by flipping when welding. It provide high efficiency and safer work area.
2. Widely used on I beam tilting , out-of-shape tank turning etc..


Detail introduction

1. The flipping tires work on turning products in 360 degree so as to adjust the position of the product.The
equipment structure is like upside down gantry type. It has four reducer to control the product piece and
very convenient to apply when flipping.

2. The flipping tires are consist of swing arm, pillar and reset device, electric control and operating
system. It also includes four standing columns attached with driving mechanism on each top. The brake
motor controls the cycloidal pinwheel reducer to drive the sprockets.

3. The chain wheel is equipped with two pulley, the pulley installed on the swing arm.On the role of the
pulley is change the movement direction of the chain and chain extension. There is a guide wheel close to the bottom of the chain wheel , that use for increasing the angle on the sprocket chain.

4. By using the post box welded structure, with enough stiffness and strength, the four standing columns
are capable of using a long period with outstanding stability.

5. There are a swing arm and a heavy hammer device on the standing columns. When the work piece
need to flip, the swing arm goes downward with a certain angle. If there is no need to flip over the work
piece, the swing arm is raised, and the chain is loosen, to make the work piece either delivered neatly.

6. The flipping tires have lifting chain to rotate the work piece, so as to solve the problem of work piece
turn slippy. There are four reducers can turn direction, either same-directional or reverse rotation.
Same-directional rotation is to flip artifact,and reverse rotation is to lift artifacts.

7. To reach the length requirement of work pieces, one side standing columns are designed fixed while
the other side of two columns respectively equipped with a sliding seat. Please fix both sides before use.

8. Control system includes: main control cabinet hand control box, hand control box with 15 meters cable connected to the control cabinet, hand control box can be used in different location of the equipment to operate equipment.

9. The manual operation box and master ark with buttons, such as power up, stop, reverse direction
selector switch and abrupt stop button.

10. Control system has motor over-current, over-voltage and over torque protection.

11. Control system is equipped with temperature detection device, stop and alarm when over-temperature.

12. Control system has simple and convenient operation, reliable operation. The operation can be close to control or remote control operation, and it is convenient to the operator at any location.




Technical Parameters

Quality Assurance and After-sales Service

1. Equipment installation and debugging is responsible by the supplier;Debugging tools, and personnel
required for coordination between the two parties to solve, installed base by the supplier to provide the
drawings, the buyer production.

2. The supplier can assist the buyer's operating personnel training.

3.The seller to the buyer service commitments: host warranty for a year, to provide door to door service,
warranty service according to the buyer's notification action within 24 hours, the buyer to assist.

4. Lifelong provide maintenance services and spare parts supply, after the warranty cost for wiring.

If you have any other special request,please just write me emial for discussion.

Company introduction

     We are located in Wuxi city, Jiangsu province, specializes in manufacturing various types of high speed, high precision roll forming machines, with more than 15 years’ experience. It has gained highly praise by customers from all over the world, due to top quality and competitive price of the products. Company principle: top quality, low price.

      Wuxi Luole Machinery Co., Ltd is a high tech enterprise . We a professional manufacturer of cold forming equipment (especially high difficulty cold formed steel), wins the trust of customers by its honesty, pragmatic operation philosophy, advanced technology, innovative design thinking, excellent quality, superior after sales service, competitive price, etc.

Main products

    We mainly produce all kinds of roof/ wall tile roll forming machine, C purlin, Z purlin, C&Z interchangeable purlin roll forming machine, solar photovoltaic forming machine, shelf column roll forming machine, guardrail roll forming machine, cable tray roll forming machine, metal deck roll forming machine, down pipe roll forming machine, rolling shutter door roll forming machine, cut to length machine, eps/pu sandwich panel production line, slitting line, automatic stacker, etc, mainly in construction use.

After sale service

1). Engineer will give free training lessons to labors in buyer’s factory.

2). The Buyer will buy the round-trip air ticket for Engineer if visa application is approved. The buyer is also responsible to bear expenses generated, e.g. visa formalities, meals, accommodation and allowance of USD80 for engineer per day.

3). During this guarantee period, we will provide spare parts without any charge in case of quality discrepancy caused by us. If the malfunctions are caused by your incorrect operations, we will provide the buyer spare parts at cost price.

4). We will charge the buyer cost price of spare parts beyond one year and provide long-term technical guide.

Photo of the factory